, Observe customers store patterns, determine the installation layout

1, first of all to understand the service's stations and the Division of labour in the service process layouts and receiver installed in staff collection line of sight in the Central main station or Office easier staircase or hallway.

2, if you store hierarchical management, it tries to install a receiver on each floor to facilitate each waiter can see their floors customer calling information.

3,Store layout directly affects the receiver number installation position and installation: Linear symmetry: total stations or receivers placed on the walls of the corridor; Twists and turns-dispersed distribution: If the operating area is small, the receiver installed in the front desk if larger business areas (greater than 100 meters receiving distance), you should consider installing multiple receivers, separate management to different rooms, and then adjust the position of staff, reach the speed of service. Distribution of both straight line and winding: General line distribution room wall installed separately on a receiver, while others turn more, consider adjusting the waiter's station, a receiver in a key area of the room, and local staff in the respective call information inform other stations after staff provide services to customers in a timely manner. May also be considered as the waiters are outfitted with mobile to the receiving host receives a call signal and timely services anytime, anywhere.

4, stores business area directly affect the number of receivers: Layering within the area of 3000 square meters, total service stations are located in the first floor or near the location of the main station, consider only installing a receiver to the main station. Layered area of 3000-5000 square meters, staff management, you should consider installing a receiver on each floor. Layered area of more than 5000 square meters, or North-South distances beyond 150 meters of the room floor, according to the wall blocking, consider installing one or more receivers. Layered area of more than 5000 square meters, but Hall partition-free business pattern, as long as the receiver and the distance does not exceed 150 m for all calls, you install a receiver if considering sight distance, you can install two receiver, so that the staff can clearly see the displayed call number. Layered area is too large, Grand and distance exceeds 200 m, you should consider installing multiple receivers or install signal booster.

Second, objective factors affecting the receiving distance: 1, a customer site installation in large electrical equipment or power control equipment, as far as possible from this interference when the product is installed. 2, customer sites, arranged a large pool or seafood and so on, as far as possible away from the humidity of the area when the product is installed. 3, customers in places such as installing large heating equipment (such as fuel oil furnace), when the product is installed as far as possible from this type of device. 4, building too many reinforced concrete columns, will be affected to a certain degree of receipt. 5, the customer premises already use other wireless products, such as radios, wireless order Po (FM of such products, our product frequency 433.92, as long as the above product band from our band, the signal will be any better) 6, the hospital near the site and large scale ultrasonic devices do not install products

Third, test calls and receive results 1, the receiver is placed at the selected location, the receiver antenna, at a 45-degree angle pointing to direction of the call. According to customer's need to adjust display waiting time (reference manual)2, more than three pagers were set different numbers (consult the manual setting), and to receive information from the farthest location for testing. 3, if the reception is poor or unstable, consider changing receiver location and then test again until you find the best receiving position. 4, the combination of both tests, one more pagers in order with a different number each time, one paper write down the number of display, select the send signal and receiving information is the most stable of the pager installed in a distant room or counter.5, repeat test as mentioned above other directions of reception.

Four installation steps: 1, plug in the power transformer, the host first plugged in the power adapter socket (note do not touch with wet hands), wait for the red light is on and connected host, and then turn on the switch for normal use. 2, check whether the receiver power on music properly. 3, install the sink fixed at the selected location, the receiver antenna, at a 45-degree angle pointing to direction of the call. 4, according to customer's need to adjust display waiting time (reference manual). Number 5, sound adjustment according to customer needs (reference manual). 6, pager number according to customer needs into customer acceptance of the number. (If you need to tune into a particular number, consult the manual). Register to keep a certain distance from the two best 30CM apart; do not register other pagers. If the individual is not registered have registered several numbers at once on a is normal, only need to register once again; if you have a registration error number, original error number should be deleted, and then register a new number.7, the installation of testing before pagers, find the best location and installation again. When installing directly with adhesive tape to stick themselves with pagers, nails can also be used in a suitable location. Note try to aim its call led to the direction of the receiver to improve reception and receiver sensitivity.8, followed by the installation of all the pagers. 9, again tried to install a call back test over its reception. 10, guidance on how customers according to the instructions.

Five, when you install the product, please note the following 1, discover products, please call the manufacturers after sales department, is not free to disassemble the product, so as to avoid causing unnecessary trouble. 2, our products Accessories the best configuration is selected according to product performance, recommend the use of original accessories (such as power adapters, batteries). In addition, the APE560 call the keys that are used properly in use when handling calls.3, when using the product, please avoid repeated frequent switching power supply, short circuit likely to cause injury or product components. 4, pagers can not in direct contact with metal base. 5, call try to paste on a smooth surface, rough surface falls off (like wallpaper). 6, humid place easy to cause oxidation, please pay attention to moisture. 7, receive information from the rainy weather and sunny days have some differences.8, pagers after installation is complete, if you want to change its location. With alcohol to penetrate the adhesive tape, then slowly removed.10, product application process should examine the adequacy of electricity products in order to avoid influence product effect. Pager battery lifespan is generally 8-12 months should to replace the battery when the indicator light (during the term of the normal led is Dim phenomenon not entirely caused by lower power, appears should promptly contact the manufacturer after-sales department).